0
0 items
₹0.00
No products in the cart.
5V 2 channel USB PC Intelligent Control Relay Module
Out of stock
SKU:008536- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support in all Windows OS.
- Onboard square USB interface, stable connection.
- Use imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military grade PCB board production.
8 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM
Out of stock
SKU:008531- Channel: 8 channel
- Relay Operating Voltage: 5V
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
1 Channel Relay Module, 30A with Optocoupler, Isolation 12V
Out of stock
SKU:008527- Channel: 1 channel
- Relay Voltage: 12V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
PC817 4 CH Optocoupler Isolation Module
Out of stock
SKU:008522- I/O Isolation for MCUs (Micro Controller Units)
- Noise Suppression in Switching Circuits
- Driving Port Signal Voltage: 3.6-24V
- Output Port Voltage Port: 3.6-30V
- Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.
NE555 Delay Monostable Switch Module Time Delay 12V
Out of stock
SKU:008516- Module based on the NE555 chip.
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- Max. load: 2200W
1 channel 5V 10A Relay Control Board Module with Optocoupler
Out of stock
SKU:008505- Channel: 1 channel
- Relay Voltage: 5V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
4 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM
Out of stock
SKU:008500- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
6-30V 1-Channel Power Relay Module with Adjustable Timing
Out of stock
SKU:008496- Operating voltage: 6-30V
- Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable.
- Trigger Signal Source: High-Level Trigger (3.0 V-24 V)
- Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A
- Optocoupler Isolation.
5-36v Switch Drive High-power MOSFET Trigger Module
Out of stock
SKU:008492 This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, PWM, motor speed control, lamp brightness. etc.
Read more
D4184 Mosfet control Module Replacement Relay
Out of stock
SKU:008486- Model: D4184
- MOS tube: 40V 50A
- Dimensions: 23mm X 16mm
- Mounting Holes Diameter: 2mm
- Compatible with MCU and control board, 3V or 5V signal.
- High-level start, low-level stop, PWM speed regulation.
5V Dual Channel Relay Module with Optocoupler
Out of stock
SKU:008481- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
150W AC-DC Buck Converter 100V-240V to 24V 6A Step Down Power Supply Module
In Stock
SKU:AB1006- Input Voltage : AC 100 – 240 V(50 HZ/60 HZ).
- Output Voltage: DC 24V.
- Output Current : Peak 6A and Nominal 5.5A (no voltage drop).
- Output Power : 150W (maximum 220 W).
- Overload Protection: Yes.
- Over Current Protection : Yes.
- Short Circuit Protection: Yes.
DFRobot 2.4GHz 6dBi Antenna with IPEX Connector
Out of stock
SKU:008452- Frequency: 2.4 GHz
- Gain: 6dBi
- Cable Length: 15cm
- Interface: IPEX MHF1
- Supports LattePanda V1
- Height: 170 mm/ 6.7 inches
25CM IPEX 1 to RP-SMA Female Connector Cable 11mm RG1.13
Out of stock
SKU:00845030CM IPEX1 to SMA Female Connector Cable 11mm RG1.13
Out of stock
SKU:008448- 30CM IPEX1 to SMA Female Connector Cable 11mm RG1.13
- Cable Type: RG1.13
- Cable Length: 30cm
- Connector Length: 11mm
50CM IPEX 1 to RP-SMA Female Connector Cable 11mm
Out of stock
SKU:008446
We specialize in providing DIY electronics kits and components, empowering makers and hobbyists to build innovative projects. We also develop final year projects for engineering students, delivering hands-on solutions for academic excellence.
Contact Us
Customer Service
Store Information
© 2025 AtomlabIndia. All rights reserved.














