0
0 items
₹0.00
No products in the cart.
- Clear filters
- Electronic Modules & Display
- Electronics Component
- IoT & Wireless
- Power Supply, Batteries & Accessories
- Power supply: DC 6.5-16v and USB 5V
- GVS output power supply: 5V or 3.3V
- No. Of Pins: 30PIN
- Processor Count: 2
- Power: 5V or 3.5–4.5V
- Supports 2G, 3G, 4G SIM cards
- TTL serial port (3.3V/5V)
- SMA antenna interface
- Flip SIM slot
- ESD protection
- AT command support
- Ideal for IoT & GPS tracking
- Onboard Mature and stable ESP-12F WiFi module, high capacity 4M Byte Flash
- The I/O port of the WiFi module and the UART program download port are all extracted, convenient secondary development
- Onboard AC-DC switch power module, supply power way support AC90-250V/DC7-12V/USB5V
- Onboard Wifi module RST reset button
- 1MB (8Mbit) Flash size.
- Very competitive price
- AP, STA, AP+STA modes available.
- Very simple AT commands, easy to use.
- Internal LWIP interface.
- Voltage: DC 3.3V (Do not use 5V supply)
- Operating Current :13-26mA
- Idle Current :10-13mA
- Operating Frequency: 13.56MHz
- Highly integrated analog circuitry to demodulate and decode responses
- Supports ISO/IEC 14443 A/MIFARE
- Processor: ESP32-C6 SoC with two 32-bit RISC-V processors (High-Performance and Low-Power).
- Memory: 512KB SRAM and 4MB Flash on-chip.
- 2.4GHz Wi-Fi 6 (802.11ax)
- Bluetooth 5.0 (LE)
- Zigbee
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Supply Voltage: 2.2 V ~ 3.6 V
- GPIO Pins: 38
- Current: 80 mA
- Data Rate: 54 Mbps.
- Flash Memory: 32Mbits
- Frequency: 2.4 GHz.
- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- ontrol Signal: Works with 5V TTL signals.
- Switching: Switches AC (up to 250V) and DC (up to 30V) loads.
- Relay Rating: Supports 5A at 240V AC.
- LED Indicator: Shows when the relay is ON.
- Wiring: 2×3-pin male header for easy connections.
- Diameter: 5mm
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800°C (Approx.)
- Dark resistance:1-20 Mohm
- Plug-n-play.
- Easy to use.
- Components are easily interconnected using 20-28 AWG wire
- 2.54 mm hole spacing
- ABS plastic material

We specialize in providing DIY electronics kits and components, empowering makers and hobbyists to build innovative projects. We also develop final year projects for engineering students, delivering hands-on solutions for academic excellence.
Contact Us
Customer Service
Store Information
© 2025 AtomlabIndia. All rights reserved.