0
0 items
₹0.00
No products in the cart.
- Operating voltage: DC4.5V-35V
- Output current: 0-5A
- Output power: 70W (max)
- PWM duty cycle: 1% -100%.
- PWM frequency:20khz
- Wide voltage DC motor speed controller.
- Operating Voltage Range: 3 ~ 9VDC
- No-load Current: 70 mA max
- Loaded Current: 200 mA max
- Operating Temperature: 50°C
- Rated Speed: 1000 RPM
- 3V to 9V DC Flat Small Size Toy Motor
- Operating Voltage: 12-24VDC
- No Load Current: 0.47A
- No-load Speed: 10000RPM
- Rated Torque: 364 g.cm
- Full Load Current: ≤2.5A
- Rated Current: ≤2.5A
- Rated Power: 28W
- Operating Voltage: 5-15VDC
- No Load Current: 0.2A
- No-load Speed: 4000RPM
- Rated Torque: 265 g.cm
- Full Load Current: ≤2A
- Rated Current: ≤2A
- Operating Voltage : 2.5 ~ 6V
- Operating Current : 130 ~ 220mA
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Outlet Outside Diameter: 7.5 mm
- Outlet Inside Diameter: 5 mm
- Model: SG90
- Weight: 9 gm
- Operating voltage: 3.0V~ 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 1.2kg-cm
- Stall torque @6.6V : 1.6kg-cm
- Made in India 32-bit Arduino board with WiFi and Bluetooth.
- Powered by Renesas R7FA4M1AB3CFM and ESP32-S3 module.
- 256 kB Flash, 32 kB SRAM, and 8 kB EEPROM.
- Built-in 12×8 programmable LED matrix for animations and games.
- Operating voltage: 5V, supports 6-24V input and USB-C.
- Advanced peripherals: DAC, CAN bus, 14-bit ADC.
- Made in India 32-bit Arduino board.
- Renesas R7FA4M1AB3CFM, 48 MHz Cortex®-M4 processor.
- 256 kB Flash, 32 kB SRAM, 8 kB EEPROM.
- Compatible with older Arduino UNO shields.
- Advanced peripherals: ADC, DAC, RTC, CAN bus.
- Supports 6-24 V input and USB-C® power.
- Use BRT (Bias Resistor Transistor)
- Easier into flash mode.
- 30% increase in radiating area
- Good stability.
- 802.11 b/g/n Standards
- Wi-Fi Direct (P2P), soft-AP
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
- Microcontroller: ATmega328
- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- Digital I/O Pins: 14
- 8 analog input port: A0 ~ A7.
- A pair of TTL level serial port transceiver : RX / TX.
- 6 PWM port: D3, D5, D6, D9, D10, D11.
- Support serial download.

We specialize in providing DIY electronics kits and components, empowering makers and hobbyists to build innovative projects. We also develop final year projects for engineering students, delivering hands-on solutions for academic excellence.
Contact Us
Customer Service
Store Information
© 2025 AtomlabIndia. All rights reserved.