- The metal gears have better wear and tear properties.
- Gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although motor gives 100 RPM at 12V, motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
- The shaft has a hole for better coupling.
- Operating Voltage(V): 12
- Operating Voltage(V): 12
- Rated Speed (RPM): 800
- Rated Torque(kg-cm): 0.5
- Stall Torque(kg-cm): 2.2
- No Load Current (A): 0.8
- Operating Voltage(V): 12
- Rated Speed (RPM): 500
- Rated Torque(kg-cm): 0.7
- Stall Torque(kg-cm): 3
- No Load Current (A): 0.06
- Onboard Mature and stable ESP-12F WiFi module, high capacity 4M Byte Flash
- The I/O port of the WiFi module and the UART program download port are all extracted, convenient secondary development
- Onboard AC-DC switch power module, supply power way support AC90-250V/DC7-12V/USB5V
- Onboard Wifi module RST reset button
- 1MB (8Mbit) Flash size.
- Very competitive price
- AP, STA, AP+STA modes available.
- Very simple AT commands, easy to use.
- Internal LWIP interface.
- Voltage: DC 3.3V (Do not use 5V supply)
- Operating Current :13-26mA
- Idle Current :10-13mA
- Operating Frequency: 13.56MHz
- Highly integrated analog circuitry to demodulate and decode responses
- Supports ISO/IEC 14443 A/MIFARE
- Processor: ESP32-C6 SoC with two 32-bit RISC-V processors (High-Performance and Low-Power).
- Memory: 512KB SRAM and 4MB Flash on-chip.
- 2.4GHz Wi-Fi 6 (802.11ax)
- Bluetooth 5.0 (LE)
- Zigbee
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Supply Voltage: 2.2 V ~ 3.6 V
- GPIO Pins: 38
- Current: 80 mA
- Data Rate: 54 Mbps.
- Flash Memory: 32Mbits
- Frequency: 2.4 GHz.
- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- ontrol Signal: Works with 5V TTL signals.
- Switching: Switches AC (up to 250V) and DC (up to 30V) loads.
- Relay Rating: Supports 5A at 240V AC.
- LED Indicator: Shows when the relay is ON.
- Wiring: 2×3-pin male header for easy connections.
- Model MG90S
- Weight 13 gm
- Operating voltage 4.8V~ 6.6V
- Servo Plug JR
- Stall torque @4.8V 1.8kg-cm
- Diameter: 5mm
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800°C (Approx.)
- Dark resistance:1-20 Mohm
We specialize in providing DIY electronics kits and components, empowering makers and hobbyists to build innovative projects. We also develop final year projects for engineering students, delivering hands-on solutions for academic excellence.
Contact Us
Customer Service
Store Information
© 2025 AtomlabIndia. All rights reserved.