0
0 items
₹0.00
No products in the cart.
8 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM
Out of stock
SKU:008531- Channel: 8 channel
- Relay Operating Voltage: 5V
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
1 Channel Relay Module, 30A with Optocoupler, Isolation 12V
Out of stock
SKU:008527- Channel: 1 channel
- Relay Voltage: 12V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
PC817 4 CH Optocoupler Isolation Module
Out of stock
SKU:008522- I/O Isolation for MCUs (Micro Controller Units)
- Noise Suppression in Switching Circuits
- Driving Port Signal Voltage: 3.6-24V
- Output Port Voltage Port: 3.6-30V
- Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.
NE555 Delay Monostable Switch Module Time Delay 12V
Out of stock
SKU:008516- Module based on the NE555 chip.
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- Max. load: 2200W
1 channel 5V 10A Relay Control Board Module with Optocoupler
Out of stock
SKU:008505- Channel: 1 channel
- Relay Voltage: 5V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
4 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM
Out of stock
SKU:008500- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
6-30V 1-Channel Power Relay Module with Adjustable Timing
Out of stock
SKU:008496- Operating voltage: 6-30V
- Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable.
- Trigger Signal Source: High-Level Trigger (3.0 V-24 V)
- Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A
- Optocoupler Isolation.
5-36v Switch Drive High-power MOSFET Trigger Module
Out of stock
SKU:008492 This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, PWM, motor speed control, lamp brightness. etc.
Read more
D4184 Mosfet control Module Replacement Relay
Out of stock
SKU:008486- Model: D4184
- MOS tube: 40V 50A
- Dimensions: 23mm X 16mm
- Mounting Holes Diameter: 2mm
- Compatible with MCU and control board, 3V or 5V signal.
- High-level start, low-level stop, PWM speed regulation.
5V Dual Channel Relay Module with Optocoupler
Out of stock
SKU:008481- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
Official Arduino UNO Q Single Board Computer Model 2GB ABX00162
In Stock
SKU:007273- Hybrid single board computer with dual-brain architecture
- Combines Qualcomm® Dragonwing™ QRB2210 MPU and STM32U585 MCU
- Supports AI-powered vision and sound applications
- Fully compatible with Arduino UNO ecosystem and shields
- Develop using Arduino IDE, Arduino Cloud, or Python® on Linux® Debian
- Includes pre-built examples, AI models, and Qwiic connector for modules
L293D Motor Driver/Servo Shield for Arduino
In Stock
SKU:007172- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
Official Arduino Nano 33 BLE Rev2 Development Board with Headers – ABX00072
In Stock
SKU:007116- Powered by nRF52840 32-bit Arm Cortex-M4 CPU @ 64 MHz
- Integrated Bluetooth Low Energy (Bluetooth LE) for wireless communication
- Supports MicroPython, enhancing development flexibility
- Built-in 9-axis IMU for accurate motion, orientation, and acceleration sensing
- Ideal for wearables, IoT devices, and real-time motion tracking applications
- Compact design with headers pre-soldered for easy prototyping
- Perfect for hobbyists and professionals working on connected technology projects
MT8870 DTMF Voice Decoding Module
Out of stock
SKU:007081- Versatile Compatibility: Works with various DTMF signals, ideal for modems, mobile radios, and more.
- User-Friendly Design: Onboard LEDs for clear signal state and adjustable timing for accurate decoding.
- Wide Applications: Integrates easily with Arduino boards (UNO, MEGA2560, DUE) for diverse projects.
- Central Office Quality: Delivers excellent performance with an internal amplifier for optimal signal reception.
- Convenient Input: Accepts both 3.5mm jack and voice input for seamless operation.
- Multi-Channel Output: 12 dedicated outputs for phone keys (0-9, *, #) and 4 additional outputs for software control.
PCF8591 Module Analog to Digital / Digital-Analog Converter Module with F-F Jumper Wire
In Stock
SKU:007026- Module PCB size: 3.6cm * 2.3cm
- PCF8591 operating voltage range of 2.5V to 6V
- 4 analog inputs programmable as single-ended or differential inputs
- VCC power supply interface external 3.3v-5v
- 8-bit successive approximation A / D converter through an analog output DAC gain
TPA3116D2 XH-M543 120W Dual Channel High Power Digital Power Amplifier Board
Out of stock
SKU:007020- Original TPA3116D2 core technology
- Easy Plug and Play Operation
- Dynamic operating Voltage Range: 12 to 24V
- High fidelity 120W out at both Channel

We specialize in providing DIY electronics kits and components, empowering makers and hobbyists to build innovative projects. We also develop final year projects for engineering students, delivering hands-on solutions for academic excellence.
Contact Us
Customer Service
Store Information
© 2025 AtomlabIndia. All rights reserved.















